FAULTS
- ‘f’ flashing
- ‘f’ staying on
- ‘n’ light comes on then flashes
- ‘n’ light stays on engine starts , then u attempt to put it in gear then the ‘n’ light starts to flash
These faults which I have listed above are the main contributions to the light appearing on the dashboard , it is important that someone with good knowledge on these items as well as having the correct tools diagnose correctly , otherwise could lead to a expensive bill.
- Clutch actuator problem
- Gear selector problem
- Crank sensor problem
- Brake switch problem / Brake light bulbs
- Clutch unit broken
| Diagnostic Trouble Code Storage Condition | Remedy | |
| P0110 | Intake Air Temperature Signal CAN-Bus Malfunction | B-016 |
| P0110 | Intake Air Temperature Signal Range/Performance | B-016 |
| P0115 | Engine Coolant Temperature Signal CAN-Bus Malfunction | B-016 |
| P0115 | Engine Coolant Temperature Signal Range/Performance | B-016 |
| P0505 | Idle Speed Signal CAN-Bus Malfunction | B-016 |
| P0505 | Idle Speed Signal Range/Performance | B-016 |
| P0560 | Battery Voltage High | C-003 |
| P0560 | Battery Voltage Low | C-003 |
| P0602 | Control Module Programming Error | C-002 |
| P0725 | Engine Speed Signal CAN-Bus Malfunction | B-016 |
| P0725 | Engine Speed Signal Range/Performance | B-016 |
| P1120 | Accelerator Pedal Position Signal CAN-Bus Malfunction | B-016 |
| P1120 | Accelerator Pedal Position Signal Range/Performance | B-016 |
| P1560 | Switched System Voltage (Ignition ON) Circuit Malfunction | C-003 |
| P1572 | ABS Active (PWM) Voltage High | B-019 |
| P1572 | ABS Active (PWM) Voltage Low | B-019 |
| P1572 | ABS Active (PWM) invalid | B-019 |
| P1600 | Replace ECU | C-002 |
| P1600 | Reprogram or Replace Electronic Control Unit (ECU) | C-002 |
| P1600 | Reprogram or Replace Electronic Control Unit (ECU) | C-002 |
| P1600 | EEPROM Comfort Values Malfunction | C-002 |
| P1600 | EEPROM System Values Malfunction | C-002 |
| P1600 | Replace Electronic Control Unit (ECU) | C-002 |
| P1607 | Clutch Actuator Position Control Error | C-004 |
| P1608 | Clutch Actuator High Temperatur | C-004 |
| P1609 | Clutch Actuator Position Sensor | C-002 |
| P1703 | Wrong Variant Configuration Programmed in Engine Controller | B-020 |
| P1703 | Brake Light Switch Signal CAN-Bus Malfunction | B-016 |
| P1703 | Brakelight Switch Range/Performance | B-017 |
| P1706 | Clutch Temperature | B-013 |
| P1707 | Clutch Adaption | B-010 |
| P1708 | Clutch Hydraulic | C-004 |
| P1710 | Wheel Speed Error | B-015 |
| P1711 | Front Left Wheel Speed Sensor No Signal | B-015 |
| P1712 | Front Right Wheel Speed Sensor No Signal | B-015 |
| P1722 | Gear Selector Serial Data | C-009 |
| P1722 | Gear Selector Serial Data Correlation | C-009 |
| P1723 | Gear Selector Redundant Data | C-009 |
| P1723 | Gear Selector Redundant Data Correlation | C-009 |
| P1725 | Shift Motor | C-013 |
| P1725 | Shift Motor Sensor Supply Voltage (12V) | C-013 |
| P1725 | Shift Motor Sensor Supply Voltage (GND) | C-013 |
| P1725 | Shift Motor Speed Signal | C-013 |
| P1725 | Shift Motor Direction Signal | C-013 |
| P1726 | Select Motor | C-014 |
| P1726 | Select Motor Sensor Supply Voltage (12V) | C-014 |
| P1726 | Select Motor Sensor Supply Voltage (GND) | C-014 |
| P1726 | Select Motor Speed Signal | C-014 |
| P1726 | Select Motor Direction Signal | C-014 |
| P1727 | Shift Motor Electric | C-013 |
| P1728 | Shift Motor Mechanic | C-013 |
| P1729 | Select Motor Electric | C-014 |
| P1730 | Select Motor Mechanic | C-014 |
| P1731 | Gearbox Actuator Temperature | C-013 |
| P1732 | Gearbox Geometry | C-013 |
| P1733 | Wrong Combination of Engine and Transmission Controller Software | B-020 |
| P1733 | Wrong Engine Type | B-020 |
| P1733 | Wrong Variant Configuration Programmed in Engine Controller | B-020 |
| P1734 | Touchpoint Adaption Not Done | B-014 |
| P1735 | Gearbox Parameters Not Learned | C-013 |
| P1740 | Gearbox Actuator Malfunction | C-013 |
| P1895 | Engine Torque Signal CAN-Bus Malfunction | B-016 |
| P1895 | Engine Torque Signal Range/Performance | B-016 |
| P1896 | Engine Torque Request Signal CAN-Bus Malfunction | B-016 |
| P1896 | Engine Torque Request Signal Range/Performance | B-016 |
| U2100 | CAN-Bus Malfunction | B-012 |
| U2103 | CAN-Bus Fault | B-012 |
| U2104 | CAN-Bus reset counter overrun | B-012 |
| U2105 | CAN-Bus no Communication with ECM (Engine Control Module) | B-012 |
| U2107 | CAN-Bus no Communication with Body Control Module | B-012 |
| U2108 | CAN-Bus No Communication with ABS (Anti-Lock Brake System |
